Vinci BMS slaves

For all Master/Slave BMS topologies

Slaves are required for any battery that uses a Master/Slave BMS topology.

Vinci BMS Slave
Vinci BMS Slave

back to top VinciLink Wired Slave

A VinciLink Wired Slave connects to a VinciLink Battery Master or to the previous Slave with a 2-wire link; it connects to its cells through wire taps.

Each VinciLink is isolated from the cell side and is not referenced to any voltage; the cell side is electrically referenced to the high voltage and is powered by the cells.

Part number Description
3MK1200D Slave, wired / VinciLink, Dissipative, 6~12 cells
3MK1600D Slave, wired / VinciLink, Dissipative, 13~16 cells
3MK2400D Slave, wired / VinciLink, Dissipative, 17~24 cells
VinciLink Slave
VinciLink Slave

Specifications

General specifications

Detailed specifications are in the Vinci BMS Manual.

back to top VinciBus Wired Slave

A VinciBus Wired Slave connects to a Battery Master through the 5-wire VinciBus; it connects to its cells through wire taps.

The cell side and the VinciBus side are isolated from each other; the cell side is electrically referenced to the high voltage, while the VinciBus side is referenced to the vehicle's chassis.

On the cell side it is powered by the cells; on the VinciBus side it is powered by the Application Module.

Part number Description
3MK1200D Slave, wired / VinciBus, Dissipative, 6~12 cells
3MK1600D Slave, wired / VinciBus, Dissipative, 13~16 cells
3MK2400D Slave, wired / VinciBus, Dissipative, 17~24 cells
VinciBus Wired Slave
VinciBus Wired Slave

Specifications

General specifications

Detailed specifications are in the Vinci BMS Manual.

back to top VinciBus Distributed Slave

A VinciBus Slave is connected to the Battery Master through a 5-wire VinciBus and to the cell boards or cell modules through 2-wire cables.

It is powered by the Application Module.

It is isolated from the high voltage, and it is electrically referenced to the vehicle chassis.

Part number Description
3MB0008W Slave, VinciBus, wired, 8 banks
VinciBus Distributed Slave
VinciBus Distributed Slave

Specifications

General specifications

Detailed specifications are in the Vinci BMS Manual.

back to top VinciNet Wired Slave

A VinciNet Wired Slave connects to the Battery Master wirelessly, and to its cells through wire taps.

It is powered by the cells.

It is isolated from the high voltage, and it is electrically referenced to the high voltage.

Part number Description
3MN1200D Slave, wired / VinciNet, Dissipative, 6~12 cells
3MN2400D Slave, wired / VinciNet, Dissipative, 13~24 cells
VinciNet Wired Slave
VinciNet Wired Slave

Specifications

General specifications

Detailed specifications are in the Vinci BMS Manual.

back to top VinciBus Fiber-optic Slave

A VinciBus Fiber-optic Slave is connected to the Battery Master through a VinciBus (wires) and to the cell boards through optical fibers.

It is powered by the Application Module.

It is isolated from the high voltage, and it is electrically referenced to earth ground.

Part number Description
3MB0004F Slave, fiber-optic / VinciBus, 4 banks
VinciBus fiber-optic slave
VinciBus fiber-optic slave

Specifications

General specifications

Detailed specifications are in the Vinci BMS Manual.

back to top Ordering

 

In this page:
VinciLink Wired Slave
VinciBus Wired Slave
VinciBus Distributed Slave
VinciNet Wired Slave
VinciBus Fiber-optic Slave
Ordering
 
© 2008~2017 Elithion™, Inc.. All rights reserved. The Elithion brand and the logo with an 'ə' (upside down 'e') are Trademarks of Elithion Inc.
Policies - Contact us - Mobile site Page published on Jul 19 2017.
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
Pop-up enlargement